Path:okDatasheet > Catalog Datasheet > MaximIC Datasheet > MaximIC-45

46BZ-T MAX6318MHUK39CX-T MAX4445ESE ICL8069BCSA MAX4178EUK-T MAX4505EUK-T MAX8211EJA MAX3086ESD MAX4332ESA MAX4304EUK-T MAX6318MHUK29DZ-T IH5042C/D MAX8211MTV MXD1005PA100 MAX365C/D MAX337EPI MAX736CWE MAX3486ECSA MAX627C/D MX581JESA MAX6316MUK40CY-T MAX1240BCPA MXD1013UA045 DG50

MaximIC Datasheets Catálogo-45

Nome do ítemFabricanteAplicativo
MAX218CWP MaximIC1.8V to 4.25V - powered, true RS-232 dual transceiver.
MAX6316LUK46BZ-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 20ms, typ watchdog timeout 25.6sec
MAX6318MHUK39CX-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms
MAX4445ESE MaximICUltra-high-speed, low-distortion, differential-to-single-ended line receiver with enable.
ICL8069BCSA MaximICLow-voltage reference, 25 ppm/C - max temp. coefficient.
MAX4178EUK-T MaximIC330MHz -3dB bandwidth, gain of +1, closed-loop buffer.
MAX4505EUK-T MaximICFault-protected, high-voltage, signal-line protector
MAX8211EJA MaximICMicroprocessor voltage monitor with programmable voltage detection. Define output current limit.
MAX3086ESD MaximICFail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver
MAX4332ESA MaximICDual, low-power, single-supply, Rail-to-Rail I/O op amp.
MAX4304EUK-T MaximICLow-noise, low-distortion op amp. Bandwidth 740MHz. Minimum stable gain 2V/V.
MAX6318MHUK29DZ-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec
IH5042C/D MaximICGeneral-purpose CMOS analog switch. Single pole, double throw (SPDT)
MAX8211MTV MaximICMicroprocessor voltage monitor with programmable voltage detection. Define output current limit.
MXD1005PA100 MaximIC5-tap silicon delay line
MAX365C/D MaximICPrecision, quad, SPST, normally open (NO) analog switch.
MAX337EPI MaximICDual 8-channel, low-leakage, CMOS analog multiplexer.
MAX736CWE MaximIC-12V, inverting carrent-mode PWM regulator.
MAX3486ECSA MaximIC3.3V-powered, +-15kV ESD-protected, 15Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 2.5Mbps. Supply voltage 3.0V to 3.6V
MAX627C/D MaximICDual non-inverting power MOSFET driver.
MX581JESA MaximICHigh precision 10 volt reference. Error +-30mV.
MAX6316MUK40CY-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 140ms, typ watchdog timeout 1.6sec
MAX1240BCPA MaximIC+2.7V, low-power, 12-bit serial ADCs in 8-pin SO. INL (LSB) +1
MXD1013UA045 MaximIC3-in-1 silicon delay line. Output delay 45ns.
DG507ACK MaximICMonolithic CMOS differential 8 channel (2 of 16) analog multiplexer.
MAX4075ANESA MaximICMicropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 8V/V, noninverting gain 9V/V, -3dB BW 50kHz.
MAX1200BEMH MaximIC+5V single-supply, 1Msps, 16-bit self-calibrating ADC
MAX6321HPUK33AY-T MaximICMicroprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec
MAX4539EPP MaximICLow-voltage, single 8-to-1 calibration multiolexer.
MAX631BESA MaximICCMOS fixed +5V output voltage,adjustable output with 2 resistors step-up switching regulator. 10% output accuracy.

<< 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 >>